电动液压剪刀式升降机注意事项？

电动液压剪刀式升降机注意事项？

The newly processed hydraulic scissor lift is prone to loose parts. In the early stage of use, due to the impact, vibration and other alternating load, as well as the impact of heat,

deformation and other factors, coupled with the cause of wear too fast, it is easy to make the original fastening parts loose. So be sure to check the equipment often whether the parts are loose traces.

新加工的液压剪刀式升降机容易出现零件松动。在使用初期，由于冲击、振动等交变载荷，以及受热、变形等因素的冲击，再加上造成磨损过快的原因，很容易使原有的紧固件松动。所以一定要经常检查设备，零件是否有松动的痕迹。

The hydraulic scissor lift may also leak because of the loose sealing. Under the influence of loose parts, vibration and heat of the machine,

leakage may occur on the sealing surface and pipe joints of the machine. Some defects, such as casting and processing,

are difficult to be found during assembly and debugging, but due to the vibration and impact effect in the process of operation,

such defects are exposed, manifested as oil leakage. Therefore, the run-in period is prone to leakage.

液压剪刀式升降机也可能因密封松动而泄漏。在机器松动的零件、振动和热量的影响下，机器的密封面和管接头可能会发生泄漏。

一些缺陷，如铸造和加工，在装配和调试过程中很难发现，但由于运行过程中的振动和冲击效应，这些缺陷暴露出来，表现为漏油。因此，磨合期容易发生泄漏。

It also takes some time for operators and equipment to get familiar with them. Before use, operators must understand the instructions and precautions,

understand the performance and principle of the machine, so as to avoid serious accidents caused by improper operation.

操作员和设备也需要一些时间来熟悉它们。使用前，操作人员必须了解说明书和注意事项，了解机器的性能和原理，以免因操作不当而造成严重事故。

The hydraulic scissor lift, as a mechanical equipment, needs a run-in period at the beginning of use,

which is not only a process of man-machine adaptation, but also a process of equipment self-adaptation.

So what do you need to pay attention to when using the elevator for the first time?

液压剪刀式升降机作为一种机械设备，在使用之初需要一个磨合期，这不仅是一个人机适配的过程，

也是一个设备自适应的过程。那么第一次使用电梯需要注意什么呢？

From the machine itself. When the equipment is first used, the wear rate is the fastest period.

The friction surface of the hydraulic scissor lift is rough, the contact area of the mating surface is small, and the pressure on the surface is uneven due to the influence of parts processing,

assembly and adjustment. During the operation of the machine, the concave and convex parts of the surface of the parts are embedded with each other for friction, and the metal debris,

as abrasive material, continues to participate in the friction, which accelerates the wear of the matching surface of the parts.

Therefore, the run-in period easy to cause parts (especially with the surface) wear, wear speed. This time if you do not pay attention to maintenance,

but carry out overload work, you will accelerate the early elevator damage.

从机器本身。设备初次使用时，磨损速度最快。液压剪刀式升降机摩擦面粗糙，配合面接触面积小，由于零件加工、装配和调整的影响，表面压力不均匀。

在机器运行过程中，零件表面的凹凸部分相互嵌入进行摩擦，金属碎屑作为磨料不断参与摩擦，加速了零件匹配面的磨损。

因此，磨合期容易造成零件（尤其是与表面）的磨损、磨损速度。这个时候如果不注意维护，而是进行超负荷工作，就会加速电梯前期的损坏。

The fitting gap of newly assembled parts of hydraulic scissor lift is small, and it is difficult to ensure the uniformity of the fitting gap due to assembly and other reasons.

Serious friction surface will cause precision fit scratch or bite phenomenon, leading to the occurrence of fault.

液压剪刀式升降机新装配零件的配合间隙小，由于装配等原因难以保证配合间隙的均匀性。严重的摩擦表面会造成精密贴合划伤或咬合现象，导致故障的发生。

The above are some Suggestions about the hydraulic scissor lift I wish I could help you.  以上是关于液压剪刀式升降机的一些建议，希望能帮到你。